This is a rundown on how you'll flash your 2022 Powerstroke with an AMDP Programmer (Added Power + PCM Swap & Transmission Tuning).
Tools required:
- Battery Charger
- Windows based Laptop
Before you start:
- Confirm all parts are present
- Fully read the installation guide
- Charge the batteries if you suspect they are low
Instructional Video
Added Power & PCM Swap Flashing Instructions
Step 1: Update software to at least 1.729 and update firmware on device by following the screen prompts.
Step 2: Send the saved oldCredits.txt file to tunes@dirtydieselcustoms.com with the information in Step 9. If this file was not saved onto the Desktop, it is not needed.
Step 3: Connect the AMDP Power Programmer to OBD2 Port of vehicle and windows based laptop then turn the key to the Run/On position. Step 4: In the Autoflasher software, select “Cable” -> “Connect”. If connection was successful, proceed to Step 5.
Step 5: Select “OBD” -> “AsBuilt” -> “Read”. In the pop up window select “ECU” then select “Enter”. Save the AsBuilt data (didsRead).
Step 6: Select “Cable” -> “Disconnect”. Disconnect Programmer from OBD2 Port.
Step 7: Install New PCM and connect the Programmer to the PCM via the supplied PCM harness. Ensure all other PCM connections are disconnected.
Step 8: Select “Service Mode” -> “Read EE”. Save the file (EE_Read).
Step 9: Email the Cable S/N and ECU S/N by right clicking on each and pasting them into the email with Order number, VIN and who you ordered it through to receive your tuning.
Step 10: Select “Service Mode” -> “Power Off”. Step 11: Select “Cable” -> “Disconnect”
Step 12: Once you have received the engine tune, select “Cable” -> “Connect”, then select “Service Mode”, “Write”, Select the tune.
Step 13: Select “Service Mode” -> “Power Off”.
Step 14: Select “Cable” -> “Disconnect”
Step 15: Connect the PCM to the Vehicle Harness
Step 16: Connect Programmer to OBD2 Port and turn the key to the On/Run Position.
Step 17: Select “OBD” -> “AsBuilt” -> “Write”, select previously saved AsBuilt data (didsRead), select “ECU”, then select “Enter”.
Step 18: Select “OBD” -> “Misc Routines” -> “Configuration Relearn”, select “ECU”, then Select “Enter”.
Step 19: Select “OBD” -> “Misc Routines” -> “PATs” -> “BCM EEPROM Read”. Save the file. If the BCM read takes longer then 10 minutes, disconnect all cables from Programmer and close the Autoflasher software. Cycle the ignition key, reopen the software, reconnect the Programmer and try again.
Step 20: Select “OBD” -> “Misc Routines” -> “PATs” -> “PATs Reset”. Select “Yes” when asked “Do you have an EEPROM read of the BCM as this was done previously. Select “Yes” when asked if you have an EEPROM read of the ECU as this was done previously. Select the BCM EEPROM Read, then select the EERead. When prompted to “Cycle Key”, key off then back to Run/On when prompted. Once the PATs reset successful message appears you can start the vehicle.
Transmission Tuning Instructional Video
Transmission Tuning
If you purchased Transmission tuning please follow the steps below.
Note:
For your truck, your TCU SN will begin with a 5 when done correctly. Once you have obtained your TCU number, please send it along with your full VIN, Cable Number, and the Order Number you purchased the tunes under.
Be sure not to use ANY of the functions on the programmer device that are not outlined in the instructions. Failure to follow instructions correctly may result i
Step 1: Connect the supplied OBD2 cable to the AMDP Powerstroke Programmer and to the vehicle’s OBD2 port. Turn the vehicle’s key to the Run/On position.
Step 2: Connect the AMDP Power Programmer to the Windows based Laptop. Step 3: Open the AutoFlasher software, select “Cable”, then Select “Connect”. If connection is successful proceed to Step 4, if it is not reinstall the USB Drivers and check the USB connections.
Step 4: Select “OBD”, then “Identify”. Select “TCU” then “Enter”. The TCU S/N will start with a “5”. Confirm the TCM is being communicated with. If not, check power connections and repeat Step 3.
Step 5: Select “OBD”, then “Get VIN”. The Cable S/N, TCU S/N and VIN need to be emailed to tunes@dirtydieselcustoms.com with your order number and who you ordered it through to receive the purchased tuning. To copy each number right click then Ctrl-V into the email.
Step 6: Once you have received the tunes via email, save them onto your computer. Repeat Steps 1-4 if you have disconnected from the vehicle.
Step 7: Select “OBD”, then “Write”, then “TCU”, select the KAM RESET file previously emailed to you. The tuning process will now begin. Once the tuning has completed turn key off then back on.
Step 8: Select “OBD”, then “Write”, then “TCU”, select the TCM Tune file previously emailed to you. Once tuning has completed turn key off then back on, you can disconnect all AMDP Powerstroke Programmer connections. Step 9: Start the vehicle and ensure there are no DTC codes or dash messages are present. If anything is present please contact Tech support.
You're all set! Go enjoy your new tuning!
